IR125Y-4 BENDER

IR125Y-4 BENDER Multi-Function Processor Module

Product  Description：

Bender Multi-Function Processor Modules, prominently represented within the COMTRAXX and condition monitoring series (such as the COM465 and EDGE500 architectures), are advanced computational and communication hubs designed for electrical safety systems. These modules serve as central processing systems that aggregate data from insulation monitoring devices, residual current monitors (RCMS), and power quality analyzers. By acting as an intelligent processing subsystem, they transform raw safety measurements into actionable network data, providing system-wide condition monitoring and automated alarm management.

Product Parameters

The technical parameters of a Bender Multi-Function Processor Module emphasize robust power options, communication bandwidth, and extensive protocol conversion capabilities:

• Power Supply Range: Highly flexible input options supporting either low-voltage DC 24V or universal AC/DC 24V to 240V at 50Hz to 60Hz.

• Power Consumption: Energy-efficient design, typically consuming less than 4 Watts or 6.5 VA under full processing load.

• Communication Hardware: Equipped with dual or single RJ45 Ethernet interfaces (10/100 Mbps) and isolated RS-485 serial ports.

• Protocol Support: Built-in protocol engines for Modbus TCP, Modbus RTU, SNMP, MQTT, PROFINET, and proprietary Bender protocols like BCOM and BMS.

• Processing Expansion: Scalable software architecture supporting distinct function modules (such as Modules A, B, C, or D) to unlock specific data-logging and parameter-setting allocations.

• Data Capacity: Integrated flash data loggers capable of concurrently tracking multiple system statuses and up to 2000 distinct data points from connected devices.

Product Advantages

Bender Multi-Function Processor Modules deliver precise control and safety coordination advantages across complex power grids:

• Centralized Monitoring and Control: Unifies all connected electrical safety devices into a single, intuitive HTML5-based web interface, eliminating the need for dedicated software installations.

• Modular Functionality: The processing capabilities can be extended or adapted via licensing modules, allowing operators to add specific features like custom email alarms, full visualization editors, or third-party device integration over time.

• Network Isolation Security: Features physically isolated Ethernet ports on advanced models, allowing complete separation between the internal industrial sensor network and the company’s external IT network.

• Advanced Self-Diagnostics: Constantly monitors connected devices for communication failure, wire breaks, or system faults, providing targeted alarm routing to minimize reaction times.

• Cloud and SCADA Readiness: Converts proprietary fieldbus signals directly into IT-friendly formats like MQTT or SNMP, facilitating direct integration into cloud systems like POWERSCOUT or enterprise management tools.

Product Applications

These processor modules are deployed in environments where electrical uptime and predictive insulation monitoring are critical:

• Medical Facilities and Hospitals: Acting as the central processor for MEDICS systems, monitoring isolated power structures in operating rooms and intensive care units to protect patient safety.

• Data Centers: Managing the continuous insulation monitoring and residual current monitoring of critical server power distribution units (PDUs).

• Industrial Production Lines: Coordinating the safety data from automated machinery and variable speed drives to prevent unexpected ground faults from halting production.

• Renewable Energy Substations: Gathering insulation and power quality parameters from large-scale solar inverters and wind turbine generators.

• Maritime and Offshore Engineering: Controlling the electrical safety monitoring systems on ships and drilling platforms where ungrounded IT distribution systems require constant oversight.

Important Precautions

To prevent configuration errors or potential hardware damage, the following precautions must be maintained:

• Electrical Disconnection Safety: Before performing physical installation, wiring modifications, or module swap-outs, ensure the main supply voltage to the housing enclosure is completely isolated.

• Network Loop Prevention: When configuring the dual Ethernet ports, verify that the network routing does not create an accidental bridge or network loop, which can cause communication blackouts.

• Register Address Verification: When utilizing the module as a gateway to Modbus TCP or PROFINET, double-check device addresses and register mapping configurations to ensure valid data transmission from individual channels.

• Firmware and Software Licensing: Ensure that the applied function module licenses precisely match the hardware generation and firmware revision of the processor module to avoid initialization failure or missing parameters.

• Environmental Protection: The module must be installed within a clean, dry control panel or IP-rated enclosure to prevent conductive moisture and dust from settling on the internal electronics, which can lead to false readings or component failure.

The structure and details of the product：

Our services：

Shipping Port:  China

Payment: Bank of Chicago, Bank of Singapore

Express cooperation: fedex, DHL, UPS and your express account

Service: Professional Sales provides 24 hours /7 days online service

Warranty: one year

Please make an inquiry for more models：

BENDER IRDH275-435

BENDER IRDH275-427

BENDER IRDH275B-415

BENDER IRDH275

BENDER IR425-D4M1C-2

BENDER iso685-D-B

BENDER IRDH275B-427

BENDER IR425-D4M1C2-2

BENDER IR425-D4-1

BENDER MK2418

BENDER MK2418A-11

BENDER 107TL47

BENDER IRDH275B-435

BENDER RCMA421 H-D-2

BENDER VMD421H

BENDER IR425-D4-2

BENDER EDS460-D-2

BENDER IRDH275-427

BENDER VMD420-D-2

BENDER RCMA420-D-1

BENDER W1-S35 B911731

BENDER VME421H-D-2

BENDER VMD421H-D-3

BENDER RCM420-D-2

BENDER IRDH-275B-435

BENDER ISOPV425-D4-4

BENDER AGH420

BENDER AGH150W-4

BENDER IRDH575B1-427

BENDER UG140P

BENDER AGH675S-7

JUSTWELL PTE. LTD. sells new and discontinued products, and purchases such specialty products through independent channels. JUSTWELL PTE. LTD. is not an authorized distributor, distributor, or representative of the featured products on this website. All product names/images, trademarks, brands, and logos used on this website are the property of their respective owners. Product descriptions, descriptions, or sales with these name images, trademarks, brands, and logos are for identification purposes only and do not imply any association or authorization with any rights holders.

This article is from the official website of JUSTWELL PTE. LTD. If reprinted, please attach this link: https://justwellltd.com .com

JUSTWELL PTE. LTD

Our main products include DCS control system spare parts, PLC system spare parts, and robot system spare parts. Our advantageous brands include Allen Bradley, Bently Nevada, ABB, HIMA, Reliance, Bender, National Instruments, Emerson Ovation, Honeywell, Siemens, Allen Bradley, ICS Triplex, FOXBORO, Schneider, GE Fanuc, Motorola, HIMA, Prosoft, and other imported industrial components. Our main products serve a wide range of electronic, metallurgical, chemical, and power plants Industries such as steel mills, rubber, cement, machinery and equipment, and construction.