eds-518a-mm-sc METSO

eds-518a-mm-sc  METSO Analog Output Modules

Product  Description：

Metso Analog Output Modules, frequently utilized within control systems like the maxDNA or Valmet DNA platforms (historically associated with Metso Automation), are high-reliability components engineered to regulate variable field equipment. These modules convert digital commands from the control system's processor into precise, continuous electrical signals. These signals are transmitted to final control elements, allowing for the exact modulation of machinery rather than simple on/off states.

Product Parameters

The technical framework of a Metso Analog Output Module centers on signal accuracy, load capability, and processing speed:

• Channel Density: Available in various configurations, typically offering 4, 8, or 16 independent analog output channels per module to match system scaling.

• Output Signal Ranges: Supports standard industrial current loops of 4-20mA and 0-20mA, as well as voltage outputs such as 0-10V DC and -10 to +10V DC.

• Digital-to-Analog Resolution: Features high-precision D/A conversion, usually operating at 12-bit to 16-bit resolution to ensure smooth control transitions.

• Load Impedance Capacity: Current outputs are typically capable of driving loops with total resistance loads up to 600 or 750 Ohms at 24V DC.

• Settling Time and Update Rate: Rapid response capabilities, with output signal updates occurring within a few milliseconds of receiving a processor command.

• Galvanic Isolation: Provides strong electrical isolation, often rated at 1500V AC or higher, between the internal system logic and the external field loops.

Product Advantages

Metso Analog Output Modules are optimized for continuous process industries where control stability is directly linked to plant safety and product quality:

• Exceptional Control Loop Stability: Designed with very low temperature drift and high linearity, ensuring the output signal remains perfectly proportional to the logic command across varying cabinet temperatures.

• Integrated HART Communication: Many modern Metso analog modules support Highway Addressable Remote Transducer (HART) pass-through, allowing engineers to calibrate, diagnose, and configure smart field instruments directly over the 4-20mA wiring.

• Advanced Fault Diagnostics: Features automated read-back verification, where the module constantly monitors the actual output current and compares it to the intended value, triggering an alarm if an open loop or short circuit is detected.

• Output State Hold on Fail: Programmable safety features allow the user to define exactly how each channel behaves if communication with the main controller is lost, with options to hold the last valid value or drop to a pre-defined fail-safe state.

• Robust Thermal Construction: Built to withstand high-density cabinet mounting without requiring specialized external cooling systems, maximizing the longevity of the electronic components.

Product Applications

These modules are critical components in heavy industrial facilities where fluid, gas, or mechanical movement must be throttled precisely:

• Control Valve Modulation: Positioning large control valves, steam governors, and dampers in power plants and chemical processing facilities to manage pressure, temperature, and fluid levels.

• Variable Speed Drive Interfacing: Sending speed and torque reference signals to Variable Frequency Drives (VFDs) managing high-power conveyor systems, fans, and pumps.

• Actuator Control: Operating pneumatic and hydraulic positioners on heavy-duty dampers, process gates, and mechanical linkages.

• Analytical Instrument Calibration: Supplying reference voltages or currents to external emissions monitoring systems and continuous gas analyzers.

• Paper Machine Controls: Managing the precise dosing pumps and steam control valves required to maintain uniform web thickness and moisture content in pulp and paper manufacturing.

Important Precautions

To maintain the precision of the output signals and prevent catastrophic hardware failures, the following guidelines must be followed:

• Shield Termination: Always use high-quality shielded twisted-pair cabling for analog output lines. To prevent ground loops that can distort the output signal, ground the shield at only one point, preferably the control cabinet ground bar.

• External Power Routing: Do not route analog signal wires parallel to high-voltage AC cables or variable frequency drive outputs. Maintain a physical separation of at least 300mm to avoid inductive noise coupling.

• Correct Load Matching: Ensure that the total resistance of the field device, including the wire resistance, does not exceed the module's maximum load specification. If the loop resistance is too high, the module will be unable to drive the full 20mA signal.

• Safe Insertion Practices: When inserting or removing modules from the backplane, confirm whether the specific sub-series supports hot-swapping. For non-hot-swappable variants, the system chassis must be completely powered down to avoid damaging the data bus.

• Channel Independent Wiring: Avoid sharing a common return wire among multiple analog output channels unless explicitly permitted by the wiring diagram. Cross-wiring channels can cause signal interference or damage the output drive circuitry.

The structure and details of the product：

Our services：

Shipping Port:  China

Payment: Bank of Chicago, Bank of Singapore

Express cooperation: fedex, DHL, UPS and your express account

Service: Professional Sales provides 24 hours /7 days online service

Warranty: one year

Please make an inquiry for more models：

METSOA413197

METSOB913S7450A

METSOB96394053A

METSOA413046

METSOA413188

METSOB962V5003A

METSOBOU8A413150

METSOBIU84A413143

METSOBOU82A413152

METSOAOH4A413139

METSOA4120074V1.1

METSOA4730024

METSOA413793A

METSOA413135AOU4

METSOA413162

METSOA48555TRE-S01

METSOA413125

METSOA413140

METSOA413050

METSOA413015NCU09

METSOA413016NCU214

METSOA413061DMU

METSOA413370ESU422138-3B

METSOA413082

METSOA413374

JUSTWELL PTE. LTD. sells new and discontinued products, and purchases such specialty products through independent channels. JUSTWELL PTE. LTD. is not an authorized distributor, distributor, or representative of the featured products on this website. All product names/images, trademarks, brands, and logos used on this website are the property of their respective owners. Product descriptions, descriptions, or sales with these name images, trademarks, brands, and logos are for identification purposes only and do not imply any association or authorization with any rights holders.

This article is from the official website of JUSTWELL PTE. LTD. If reprinted, please attach this link: https://justwellltd.com .com

JUSTWELL PTE. LTD

Our main products include DCS control system spare parts, PLC system spare parts, and robot system spare parts. Our advantageous brands include Allen Bradley, Bently Nevada, ABB, HIMA, Reliance, Bender, National Instruments, Emerson Ovation, Honeywell, Siemens, Allen Bradley, ICS Triplex, FOXBORO, Schneider, GE Fanuc, Motorola, HIMA, Prosoft, and other imported industrial components. Our main products serve a wide range of electronic, metallurgical, chemical, and power plants Industries such as steel mills, rubber, cement, machinery and equipment, and construction.